Youssef Mohamed

Responsible for Secondary Scope for Different Projects in different regions including ( Single Line Diagram , Protection Logic Diagram, CT Sizing, VT Sizing , Termination Sheets and Cable Schedules, AC , DC and Control Cables design, Battery and Battery Charger Sizing , Signal List , Schematic Drawings Review) Projects: I - Egypt • South Kayan Extension Project 220/22 KV • Al Balat Substation Extension 220/66/22 KV - Tender II - KSA • Modification of MV Network at Spark city • Power Factor Correction Project at CAPD-6 with Aramco • ABQIQ Relays Replacement for 21 Substations with Aramco • NWC Smart Power Meters • 13.8 KV MV SWGR Replacement at MANFOUHA with NWC • Upgrading Protection System at JUBA • Replacement of LV SWGR at HW- GOSP 4 with Aramco III- Jordan • NEPCO Relay / SAS Replacement for the main 3 Substations in the country

Projects I - Silver Gate Mall - Prepare Shop Drawings for Landscape Lighting - Prepare Lux Distribution for Lighting System in Basement Floor - Prepare Riser Diagrams for Power and Light Current Works - Prepare As Built Drawings for Electrical and Light Current Systems ( Lighting - Power - Cable Routing - Fire Alarm - CCTV - MATV - Telephone - DATA and Public Address) - Attended Factory tests for 17 Low Voltage Panel Boards to Check Safe Performance of the Panels - Prepare RFI - Prepare QS for Project Materials ( Conduits - Wires&Cables -Trays -etc...) - Prepare Monthly Invoices II - Bank Misr - Review Tender Documents - Prepare Shop Drawings for Different Electrical and Light Current Works ( Lighting - HVAC - Fire Alarm - CCTV - Access Control - MATV - Evacuation) - Sizing Cable Trays and Conduits based on Filling Ratio Limitation - Select Appropriate Locations for Panel Boards - Prepare Panel Schedules for Different Panels - Prepare QS for Project Materials - Select Suitable Sizes for Light Current Racks III- The Crown Infrastructure A- phase 02 - Prepare Shop Drawings for Landscape Lighting - Prepare Panel Schedules for Landscape Panels - Prepare VD Calculations - Prepare QS for LC Boxes - KWHM Boxes - Cables - Landscape Lighting Fixtures - Review Technical Offers for Panel Boards - KWHM & LC Boxes - Select Appropriate Locations for ductbanks B- Phase 03 - Review Tender Documents - Prepare LOD - Review Load Estimation Sheet - Prepare Shop Drawings for MV & LV Cable Routing - Select Appropriate Locations for Transformer Kiosk ,Landscape Panels ,Pillars ,Coffret and ductbanks - Prepare Voltage Drop Calculations for the Whole Phase and Suggest an Suitable Cable Sizing Based on VD Limitations - Prepare RFI IV- VINCI Infrastructure - Review Tender Documents - Prepare Shop Drawings for MV&LV Cable Routing and Street Lighting - Select Appropriate Locations for Transformer Kiosk ,Landscape Panels ,Pillars ,Coffret and ductbanks

Training in the Field of Cable Construction - Selection - Manfucating and Testing

Training in Automation field :Classic Control - PLC - Motor Drives - Sensors

Electrical Works in Automation Field

Distribution course that Covered The Following Topics : -Load Estimation -Zoning -Bulk Equipment Selection ( Transformers, Generators, UPS) - LV / MV Switchgear Components - Lighting Design Using Dialux, Autocad - Small Power - MEP - Panel Schedule - Voltage Drop and Short Circuit Calculation - Earthing Design - Lightning Design - Cable Sizing - Cable Routing - Infrastructure - Street Lighting Design

MV Premolded Cables and accessories

Internship at Automation field : Classic Control - PLC - Motor Basics - HMI - AC Drives - Soft Starters

Courses - Power System Analysis - Selected topics in electrical power and machines - Power Electronics Systems - Power Generation from Renewable sources - Planning of Power Systems

Graduation Project: Electrical Power Planning & Distribution in a Compound Graduation Project Grade : A+